---

XgUartAvr

Data Structures
struct	_UARTDCB
	UART device control block structure. More...
struct	_UARTDCB
	UART device control block structure. More...
Typedefs
typedef _UARTDCB	UARTDCB
Functions
int	UartAvrGetRaw (u_char *cp)
	Get raw byte from the UART receiver register.
int	UartAvrPutRaw (u_char ch)
	Put raw byte to the UART transmit register.
int	UartAvrInput (NUTDEVICE *dev)
	Wait for input.
int	UartAvrOutput (NUTDEVICE *dev)
	Initiate output.
int	UartAvrFlush (NUTDEVICE *dev)
	Wait for output buffer empty.
int	UartAvrIOCtl (NUTDEVICE *dev, int req, void *conf)
	Perform on-chip UART control functions.
int	UartAvrInit (NUTDEVICE *dev)
	Initialize on chip uart device.

---

Typedef Documentation

typedef struct _UARTDCB UARTDCB

UART device control block type.

---

Function Documentation

int UartAvrFlush (  NUTDEVICE *    dev )

Wait for output buffer empty. If the output buffer contains any data, the calling thread is suspended until all data has been transmitted. Parameters: dev  Indicates the UART device. Returns: 0 on success, -1 otherwise.

int UartAvrGetRaw (  u_char *    cp )

Get raw byte from the UART receiver register. Parameters: cp  Pointer to the character buffer. Returns: 1 if a byte has been available, 0 otherwise.

int UartAvrInit (  NUTDEVICE *    dev )

Initialize on chip uart device. Prepares the device for subsequent reading or writing. Enables UART transmitter and receiver interrupts. Applications should not use this function, but call NutDeviceOpen(). Parameters: dev  Identifies the device to initialize. Returns: 0 on success, -1 otherwise.

int UartAvrInput (  NUTDEVICE *    dev )

Wait for input. This function checks the input buffer for any data. If the buffer is empty, the calling thread unknown reference! will be blocked until at least one new character is received or a timeout occurs. Parameters: dev  Indicates the UART device. Returns: 0 on success, -1 on timeout.

int UartAvrIOCtl (  NUTDEVICE *    dev, int    req, void *    conf )

Perform on-chip UART control functions. Parameters: dev  Identifies the device that receives the device-control function. This pointer must have been retrieved previously by using the NutDeviceOpen() function. req  Requested control function. May be set to one of the following constants: UART_SETSPEED, if conf points to an u_long value containing the baudrate. UART_GETSPEED, if conf points to an u_long value receiving the current baudrate. UART_SETDATABITS UART_GETDATABITS UART_SETPARITY UART_GETPARITY UART_SETSTOPBITS UART_GETSTOPBITS UART_SETSTATUS UART_GETSTATUS UART_SETREADTIMEOUT UART_GETREADTIMEOUT UART_SETWRITETIMEOUT UART_GETWRITETIMEOUT Parameters: conf  Points to a buffer that contains any data required for the given control function or receives data from that function. Returns: 0 on success, -1 otherwise. Note: Timeout is limited to the granularity of the system timer.

int UartAvrOutput (  NUTDEVICE *    dev )

Initiate output. This function checks the output buffer for any data. If the buffer contains at least one character, the transmitter is started, if not already running. The function returns immediately, without waiting for the character being completely transmitted. Any remaining characters in the output buffer are transmitted in the background. Parameters: dev  Indicates the UART device. Returns: 0 on success, -1 otherwise.

int UartAvrPutRaw (  u_char    ch )

Put raw byte to the UART transmit register. Parameters: ch  Character to transmit. Returns: 1 if the byte has been stored in the transmit register, 0 if the transmitter is busy.

---